Enterprise Only: Performance Replication requires Vault Enterprise with the Multi-Datacenter & Scale Module.
Vault replication also includes a complete API. For more information, please see the Vault Replication API documentation
»Activating Performance Replication
»Activating the Primary
To activate the primary, run:
$ vault write -f sys/replication/performance/primary/enable
There is currently one optional argument:
specifies the cluster address that the primary gives to the secondaries.
NOTE: Use this parameter if the primary's cluster address is not directly accessible and must be accessed via an alternate path/address (e.g. through a TCP-based load balancer). Otherwise, the secondaries use the configured cluster address to connect to the primary. See the Vault High Availability with Consul guide for an example Vault server configuration.
»Fetching a Secondary Token
To fetch a secondary bootstrap token, run:
$ vault write sys/replication/performance/primary/secondary-token id=<id>
The value for
id is opaque to Vault and can be any identifying value you want;
this can be used later to revoke the secondary and will be listed when you read
replication status on the primary. You will get back a normal wrapped response,
except that the token will be a JWT instead of UUID-formatted random bytes.
»Activating a Secondary
To activate a secondary using the fetched token, run:
$ vault write sys/replication/performance/secondary/enable token=<token>
You must provide the full token value. Be very careful when running this command, as it will destroy all data currently stored in the secondary.
The secondary will use the address embedded in the bootstrap token, which is the
primary's redirect address to make a connection to the primary. If the primary
has no redirect address (for instance, if it's not in an HA cluster), you'll
need to set the
primary_api_addr parameter to specify the primary's API
address at secondary enable time.
Once the secondary is activated and has bootstrapped, it will be ready for service and will maintain state with the primary. It is safe to seal/shutdown the primary and/or secondary; when both are available again, they will synchronize back into a replicated state.
Note: if the secondary is in an HA cluster, you will need to ensure that each standby is sealed/unsealed with the new (primary's) unseal keys. If one of the standbys takes over on active duty before this happens it will seal itself to remove it from rotation (e.g. if using Consul for service discovery), but if a standby does not attempt taking over it will throw errors. We hope to make this workflow better in a future update.
On a production system, after a secondary is activated, the enabled auth methods should be used to get tokens with appropriate policies, as policies and auth method configuration are replicated.
The generate-root command can also be used to generate a root token local to the secondary cluster. After the secondary is activated, it will need to use the unseal or recovery keys from the Primary when generating a new root token or performing other commands that require unseal or recovery keys.
»Dev-Mode Root Tokens
To ease development and testing, when both the primary and secondary are
running in development mode, the initial root token created by the primary
(including those with custom IDs specified with
-dev-root-token-id) will be
populated into the secondary upon activation. This allows a developer to keep a
~/.vault-token file or
VAULT_TOKEN environment variable when
working with both clusters.
Also, reference the Performance Replication with Mount Filters guide.
»Managing Vault Performance Replication
Vault's performance replication model is intended to allow horizontally scaling Vault's functions rather than to act in a strict Disaster Recovery (DR) capacity. For more information on Vault's disaster recovery replication, look at the general information page.
As a result, Vault performance replication acts on static items within Vault, meaning information that is not part of Vault's lease-tracking system. In a practical sense, this means that all Vault information is replicated from the primary to secondaries except for tokens and secret leases.
Because token information must be checked and possibly rewritten with each use (e.g. to decrement its use count), replicated tokens would require every call to be forwarded to the primary, decreasing rather than increasing total Vault throughput.
Secret leases are tracked independently for two reasons: one, because every such lease is tied to a token and tokens are local to each cluster; and two, because tracking large numbers of leases is memory-intensive and tracking all leases in a replicated fashion could dramatically increase the memory requirements across all Vault nodes.
We believe that this performance replication model provides significant utility for horizontally scaling Vault's functionality. However, it does mean that certain principles must be kept in mind.
»Always Use the Local Cluster
First and foremost, when designing systems to take advantage of replicated Vault, you must ensure that they always use the same Vault cluster for all operations, as only that cluster will know about the client's Vault token.
»Enabling a Secondary Wipes Storage
Replication relies on having a shared keyring between primary and secondaries and also relies on having a shared understanding of the data store state. As a result, when replication is enabled, all of the secondary's existing storage will be wiped. This is irrevocable. Make a backup first if there is a remote chance you'll need some of this data at some future point.
Generally, activating as a secondary will be the first thing that is done upon setting up a new cluster for replication.
»Replicated vs. Local Backend Mounts
All backend mounts (of all types) that can be enabled within Vault default to being mounted as a replicated mount. This means that mounts cannot be enabled on a secondary, and mounts enabled on the primary will replicate to secondaries.
Mounts can also be marked local (via the
-local flag on the Vault CLI or
local parameter to
true in the API). This can only be performed
at mount time; if a mount is local but should have been replicated, or vice
versa, you must disable the backend and mount a new instance at that path with
the local flag enabled.
Local mounts do not propagate data from the primary to secondaries, and local mounts on secondaries do not have their data removed during the syncing process. The exception is during initial bootstrapping of a secondary from a state where replication is disabled; all data, including local mounts, is deleted at this time (as the encryption keys will have changed so data in local mounts would be unable to be read).
In normal Vault usage, if Vault has at least one audit device configured and is unable to successfully log to at least one device, it will block further requests.
Replicated audit mounts must be able to successfully log on all replicated clusters. For example, if using the file audit device, the configured path must be able to be written to by all secondaries. It may be useful to use at least one local audit mount on each cluster to prevent such a scenario.
»Never Have Two Primaries
The replication model is not designed for active-active usage and enabling two primaries should never be done, as it can lead to data loss if they or their secondaries are ever reconnected.
Local backend mounts are not replicated and their use will require existing DR mechanisms if DR is necessary in your implementation.
If you need true DR, look at the general information page for information on Vault's disaster recovery replication.